Wi-Fi Site Surveys: Why Coverage Problems Start Before Installation

Wireless access point installed on an office ceiling

In Field of Dreams, a voice says, “If you build it, they will come.” This isn’t the case with Wi-Fi. Without any planning, you’ll be left with a flood of tickets to the helpdesk.

Most coverage issues occur due to poor planning. A Wireless Site Survey can identify these.

Identifying Poor Planning

You’ll quickly see signs that something is wrong:

  • No coverage in the conference area.
  • Freezing video calls near the break room.
  • Devices cutting out in one aisle.
  • Speeds on one desk are fast but slow 10 ft away.

Most teams will look at the internet and router to identify what the issue is. Most of the time, however, it is due to poor planning and poor access point placement.

Changing hardware won’t solve the issue; you’re just moving it. Having them planned properly from the start will save you a lot of money.

Types of Survey

A site survey will show you how your signal is behaving within a specific building. The main types of site surveys are:

  • Predictive: The engineer will upload a floor plan. They’ll add different wall types and create virtual access points. This is useful for new builds and planning budgets. Accuracy will depend on the information inputted. If the wall type is incorrect, your results will not be accurate.
  • On-site: The engineer will go onsite with a survey tool and test each access point. The tool will give real data to give you an idea of the signal strength, noise and channel overlap. You can carry out a passive survey or an active one where you test your throughput. This is best suited for existing buildings and high value areas.

Most projects will have a mix of both. Using the predictive model to plan, then confirming with an onsite survey.

Interference & Building Materials

All buildings will cause interference to your wireless signal. Depending on the materials being used, some will absorb or block the radio waves more than others. Two offices with the same layout can behave very differently.

Drywall and normal glass won’t cause much of a slowdown, but once you start using thicker materials you’ll see a big drop. Brick and concrete will absorb a large portion of the signal. Low-E glass (energy efficient windows) will have a thin layer of metal to reflect the radio waves. Metal shelving, fire doors and lift shafts are the worst. Water can also cause a lot of issues. Aquariums, piping and even a busy room of people can reduce your signal more than most would expect.

The higher the frequency, the worse the signal will get through walls. 5GHz will provide more data than 2.4GHz but won’t penetrate walls as well. The new 6GHz band also doesn’t have great range. Your access points may not cover as well on one band.

The more networks, microwaves and Bluetooth devices around, the more interference you’ll have. The 2.4GHz band is the most congested. Only 3 channels are non-overlapping in the US (1, 6 and 11). If two nearby access points are on the same channel they will slow each other down. The spectrum scan will show you what is already in use. This makes it easy for the designer to get a clear understanding of what’s going on.

Access Point Location & Cabling

Using the data you collected from the survey will help you decide where to place your access points.

  • Place them centrally on the ceiling.
  • Plan to get a signal of -67dBm at the edge of the cell. This is a popular target for voice/video.
  • Some cell overlap should be planned for so devices can roam.
  • Plan for capacity. If there are 30 people in the room with 60 devices, you’ll need more than one strong signal.

Your access points will need clean cabling back to the network. Ethernet cables can only be 100m long (90m permanent link + patch cords). Use Cat6 or above. Check the PoE budget on your switch. Newer access points may require multi-gigabit ports.

Make sure to plan your cable routes before the walls go up. Getting new cables in can be slow and expensive. All cabling should be labelled. All drops should be documented. Having a good guide in place for your data network cables can help the team put standards in place early. A good structured cabling install will ensure your wireless is reliable.

Post Installation Validation

Once your access points are installed, you should do a validation. This will ensure your network is performing as designed.

Check:

  • Signal strength
  • Roaming
  • Throughput using real devices
  • Channels and power levels

The engineer will provide heat maps and a report. This can be used as your baseline for future work.

This is not a one-off process. Adding furniture, new tenants or a new partition can change the coverage. If something major changes, check again.

Future

More and more devices are being used. Laptops, phones, badges, cameras and sensors all use the same air. Wi-Fi 6E and Wi-Fi 7 are getting faster but also new bands. However, the 6GHz band doesn’t have such a great range so many sites will need extra access points. They’ll need to be planned carefully.

Planning is more valuable. A site survey is a cheap way to ensure your Wi-Fi is designed rather than guessed at. This ensures your network infrastructure services are focused on getting it right the first time.

Ready to Transform Your IT Infrastructure?

Contact Arch Enterprise, Inc. today for expert consultation and professional installation services tailored to your business needs.

Trusted by businesses nationwide24/7 SupportCertified Technicians